ML-4D/OUT-E
4-Channel Line Output Dante Converter with built-in DSP Mixer
Built-in DSP 4 line outputs Dante converter to respond to various needs of contractor market and professional audio scene.
- Power : PoE class 0, TASCAM PS-P1220E
- Power consumption : 4W
- Dimensions : 214(W) × 44.45(H) × 136.1(D)mm
- Weight : 863g
- 4 balanced line output (Euroblock)
- 4 Dante input/output
- Supports PoE (Power over Ethernet)
- Includes a variety of DSP functions for optimal use in different scenes/environments (Output effects, 4 in/4 out matrix mixer)
- 2 types of user control software available for Windows/Mac/iOS/Android devices:
For full control: input/output routing selection, DSP/design/scene settings of the complete system, etc.
For simple control: simple app design for only the necessary functions such as area volume settings, etc. - Half-rack mountable size
- Equipped with signal indicators that monitor line output signals
- ML-4D/OUT-E × 1
- Installation brackets × 2
- Euroblock plugs × 4
- Cable band kit × 1
- Owner's Manual (including warranty) × 1
The ML-4D/OUT-E is a compact converter that converts Dante input signals into 4-channel line output signals. With half the size of a standard 1U rack, the ML-4D/OUT-E is suitable for different Dante systems as an exquisite analog output unit. The built-in DSP mixer enables small scale systems to fully perform with a variety of input/output models the TASCAM Dante Compact Processor Series offers. ML-4D/OUT-E supports up to 96kHz/24bit and uses Euroblock connectors for analog line output.
4 line output, 4 Dante input/output
The ML-4D/OUT-E not only converts Dante signals into 4-channel line signals; it can also convert them into 4-channel Dante output signals, making it possible to direct these to a Dante established network using the built-in DSP matrix mixer.
Built-in 4 in/4 out matrix mixer
Using the built-in matrix mixer, users can mix 4-channel Dante inputs and configure settings on each of the four output zones. The matrix mixer is also equipped with a ducking function and an ambient noise compensator function, which detects the level of environmental sounds and automatically adjusts the input level of the source.
Input/output routing
Flexible routing allows users to choose the output zone of 4 Dante inputs or the built-in matrix mixer as 4 line output and/or 4 Dante output. The ML-4D/OUT-E can be also used a as a simple line output unit by bypassing the matrix mixer.
10 band EQ and a variety of output effects included
10 band EQ, high pass filter, low pass filter, delay, and limiter effects included. They can be finely adjusted depending on the powered speakers, or to the environment in which the unit is used.
PoE supported
Power supply can be provided to the unit via PoE (Power over Ethernet). No need for AC adaptors; power supply construction fees and installation costs can be reduced by using a PoE compatible network switch.
Remote control via control software
Controlling effects or the matrix mixer can be easily done through the dedicated control software; depending on the amount of controls the user needs, there are two types:
- TASCAM DCP CONNECT, designed for system integrators/managers that handle the configuration and settings of an entire system.
- TASCAM EZ CONNECT, designed for end-users and allowing them to use simple controls.
Additional Features
Flexible routing
Read More
Installable according to usage/environment
Read More
Installable according to usage/environment
Read More
Features at a Glance
- 4 balanced line output (Euroblock)
- 4 Dante input/output
- Supports PoE (Power over Ethernet)
- Up to 24bit/96kHz
- Includes a variety of DSP functions for optimal use in different scenes/environments (Output effects, 4 in/4 out matrix mixer)
- Supports Dante daisy chain; this allows two Dante Compact Processor models to be connected without a network switch
- Flexible scene preset function allows to work in different area situations (Up to 50 presets)
- 2 types of user control software available for Windows/Mac/iOS/Android devices:
For full control: input/output routing selection, DSP/design/scene settings of the complete system, etc.
For simple control: simple app design for only the necessary functions such as area volume settings, etc. - Remote control via GPI and Dante
- Half-rack mountable size
- Equipped with indicators that show LAN/Dante connection status and sample rate
- Equipped with signal indicators that monitor line output signals
- Configurable reference level (via remote control only)
- Surface rack mountable angles for installation under desks included
- Optional accessories:
AC adapter PS-P1220E for redundant power supply available
Rack-mountable shelf AK-RS1 to install and store two Dante Compact Processor models in a 19 inch rack case
Dante Compact Processor Series - New Upgraded Version 1.04 of Dante Module Firmware Released
Learn More
Dante Compact Processor Series - New Upgraded Version 1.2.0.6 of Dante Module Firmware Released
Learn MoreYou might also like
Spec description
| General | |
| Formats and channels | 44.1/48/88.2/96kHz,16/24-bit, 4 channels |
| Input/output ratings | |
| DATA/DATA+PoE connectors | |
| Connector | RJ-45 |
| Transmission protocol | Dante |
| Gigabit Ethernet standard | 1000BASE-T (IEEE 802.3ab) |
| Cables | category 5e or faster STP cables |
| ANALOG OUT connectors | |
| Connector | Euroblock (balanced) 3.81 mm pitch |
| Nominal output levels | +4 dBu (when Ref. Level not -9 dBFS) +6 dBu (when Ref. Level set to -9 dBFS) |
| Maximum output level (switchable) | +15 dBu (Ref. Level: -9 dBFS) +18 dBu (Ref. Level: -14 dBFS) +20 dBu (Ref. Level: -16 dBFS) +22 dBu (Ref. Level: -18 dBFS) +24 dBu (Ref. Level: -20 dBFS) |
| Output impedance | 200 Ω or lower |
| Control input/output | |
| External control connectors (CONTROL) | |
| Connectors | Euroblock 3.81mm pitch |
| 10V/CONTROL/GND connectors | Connect variable resistors (10kΩ recommended) |
| Other | |
| Power | PoE class 0 TASCAM PS-P1220E AC adapter (sold separately) |
| Power consumption | 4W |
| Dimensions | 214 x 44.45 x 136.1 mm (W x H x D, including protrusions) |
| Weight | 863 g |
| Operating temperature range | 0°C-40°C |
| Included items | Installation brackets, Euroblock plugs, Cable band kit, Owner's manual (including warranty) |
Audio performance
| DANTE IN → LINE OUT | |
| Frequency response | +/-0.5 dB: 20 Hz - 20 kHz(44.1/48kHz sampling frequency, JEITA) +/-0.5 dB: 20 Hz - 40 kHz(88.2/96kHz sampling frequency, JEITA) |
| Distortion (THD+N) | 0.002 %(when -1 dBFS input, 44.1/48/88.2/96kHz samplingfrequency, JEITA) |
| S/N ratio | 108 dB (44.1/48/88.2/96kHz sampling frequency, JEITA) |
| Crosstalk | 100 dB (44.1/48/88.2/96kHz sampling frequency, JEITA) |
| Dynamic range | 108 dB (44.1/48/88.2/96kHz sampling frequency, JEITA) |
Note: JEITA indicates compliance with JEITA CP-2150
MM-4D/IN, ML-4D/OUT, MM-2D, AE-4D comparison chart
Input channels
| Products | Analog (Mic/Line) | Digital (AES/EBU) | Digital (Dante) |
| MM-4D/IN-X | 4ch | - | 4ch |
| MM-4D/IN-E | 4ch | - | 4ch |
| ML-4D/OUT-X | - | - | 4ch |
| ML-4D/OUT-E | - | - | 4ch |
| MM-2D-X | 2ch | - | 4ch |
| MM-2D-E | 2ch | - | 4ch |
| AE-4D | - | 4ch | 4ch |
Output channels
| Products | Analog (Line) | Digital (AES/EBU) | Digital (Dante) |
| MM-4D/IN-X | - | - | 4ch |
| MM-4D/IN-E | - | - | 4ch |
| ML-4D/OUT-X | 4ch | - | 4ch |
| ML-4D/OUT-E | 4ch | - | 4ch |
| MM-2D-X | 2ch | - | 4ch |
| MM-2D-E | 2ch | - | 4ch |
| AE-4D | - | 4ch | 4ch |
Input/Output/GPI connectors
| Products | Analog | Digital (AES/EBU) | Digital (Dante) | GPI |
| MM-4D/IN-X | XLR | - | RJ45 | - |
| MM-4D/IN-E | Euroblock | - | RJ45 | Euroblock |
| ML-4D/OUT-X | XLR | - | RJ45 | - |
| ML-4D/OUT-E | Euroblock | - | RJ45 | Euroblock |
| MM-2D-X | XLR | - | RJ45 | - |
| MM-2D-E | Euroblock | - | RJ45 | Euroblock |
| AE-4D | - | XLR | RJ45 | - |
Information
| Latest version info | |
| Firmware | V1.04 |
| Dante Module Firmware | V1.2.0.6 |
- In firmware V1.03 and earlier, when the total amount of packet data sent/received exceeded 2 GB due to prolonged operation after power-on, the network connection would become unavailable or the network would be disconnected.
This issue has been fixed in V1.04.
- In V1.2.0.5, remote connection could still become interrupted on networks where multicast was used. This problem was confirmed and fixed.
