IF-AN16/OUT
16 CHANNEL ANALOG OUTPUT EXPANSION CARD
Supporting models : TASCAM Sonicview 24XP / TASCAM Sonicview 16XP / DA-6400 / DA-6400dp
The IF-AN16/OUT is an optional 16-channel analog output interface card for the TASCAM expansion slot system. Equipped with two D-sub 25 pin for analog outputs.
- Formats and channels : 16 channels at 44.1/48/88.2/96kHz, 16-bit/24-bit
- Connector : D-Sub 25-pin
- Locking screws : No. 4-40 UNC (inch type)
- Nominal output levels : +4 dBu, +6 dBu (only when maximum output level is +15 dBu)
- Maximum output levels : +24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu (Switched according to nominal level of device installed in)
- 16 channels of analog outputs
- Built-in output attenuation for each channel: 0 to -14dB (0.5steps)
- Two 8-channel D-sub 25pin balanced audio signal outputs (channels 1-8 and 9-16)
- Compatible with the TASCAM Expansion Slot system
- IF-AN16/OUT x 1
- Owner's Manual with Warranty
Features at a Glance
- 16 channels of analog outputs
- Built-in output attenuation for each channel: 0 to -14dB (0.5steps)
- Two 8-channel D-sub 25pin balanced audio signal outputs (channels 1-8 and 9-16)
- Compatible with the TASCAM Expansion Slot system
You might also like
Spec description
| Formats and channels | 16 channels at 44.1/48/88.2/96kHz, 16-bit/24-bit |
| Analog audio output ratings | |
| ANALOG 1-8/9-16 OUT connectors | |
| Connector | D-Sub 25pin |
| Locking screws | No.4-40 UNC (inch type) |
| Nominal output levels | +4 dBu, +6 dBu (only when maximum output level is +15 dBu) |
| Maximum output levels | +24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu (Switched according to nominal level of device installed in) |
| Output impedance | 200Ω or lower |
| Output attenuation | 0 to -14 dB (in 0.5dB steps) |
| Dimensions | 107(W) × 40(H) × 161.5(D) mm (including protrusions) |
| Weight | 240g |
Audio performance
| Frequency response | +0.1dB/-0.5dB : 20Hz/20kHz (-16dBFS input, 44.1/48kHz sampling frequency, JEITA) +0.1dB/-1.0dB : 20Hz/40kHz (-16dBFS input, 88.2/96kHz sampling frequency, JEITA) |
| Distortion (THD+N) | 0.001% or less (0dBFS input, 1kHz, 44.1/48/88.2/96kHz sampling frequency, JEITA) |
| S/N ratio | 110dB or higher (44.1/48/88.2/96kHz sampling frequency, JEITA) |
| Dynamic range | 110dB or higher (44.1/48/88.2/96kHz sampling frequency, JEITA) |
| Crosstalk | 110dB or higher (1kHz, 44.1/48/88.2/96kHz sampling frequency, JEITA) |
- Applicable load impedance：2kΩ or higher
- 0dBu=0.775Vrms
- When output attenuation set to 0dB
Pin assignments
