-------------------------------------------------------------------------------------------------------------
Latest information (2024.4.4)
-------------------------------------------------------------------------------------------------------------
The most recent versions of the TASCAM IO CONTROL are as follows.

Version: V1.1.1 (Previously V1.1.0 Updated at this time)

We request that you always use the latest version for TASCAM IO CONTROL.
For information about the latest version, check the TEAC Global Site (http://teac-global.com/)

-------------------------------------------------------------------------------------------------------------
Information about related equipment, software and other versions
-------------------------------------------------------------------------------------------------------------
The following information about versions is current as of June 19, 2024.
Please check individual product pages for the latest information.

- TASCAM Sonicview 16/24
　　- Firmware      : V1.6.1  （date of latest update: 19 June 2024）

　　- Dante module firmware
      　< Brooklyn II >  （date of latest update: 4 April 2024）
           Product Version             : V1.0.2   
           Software Version            : V1.0.2.1
           Firmware Version            : V1.0.2.1
           Dante Firmware Version      : V4.2.3.13

        < Brooklyn 3 >    （date of latest update: 4 April 2024）
           Product Version             : V1.0.2
           Software Version            : V1.0.2.1
           Firmware Version            : V1.0.2.1
           Dante Firmware Version      : V4.2.7.7

  *************************************************************************************************
  The Dante Module update file differs between Dante Model Brooklyn II and Brooklyn 3.
  To check the current model, follow the steps below and proceed to update:
  (Please refer to the "TASCAM Dante module update manual" for the update instructions.)

  [To verify the Dante model]
   - Checking with Dante Controller
 　   (1) After launching Dante Controller, double-click the name of the device being used on the Routing tab.
 　   (2) Click the Status tab. The model name is written to the right of “Model” under Dante Information.
   - On a Sonicview console with firmware V1.5.3 and later:
      Main MENU > Rear Panel Setup > Dante Setup > Sante Settings Tab > Brooklyn II or 3 can be seen in the MODULE's Dante Model
   - On a Sonicview console with firmware before V1.5.3;
     you can verify the Dante model with the serial number printed on the main unit:
      - Serial number [223xxxx, 226xxxx, 229xxxx, 2362xxx, 2372xxx, 2382xxx, 2392xxx] uses Brooklyn II
      - Serial number [232xxxx, 234xxxx, 235xxxx, 2363xxx, 2373xxx, 2383xxx, 2393xxx] uses Brooklyn 3
  *************************************************************************************************

- "TASCAM Sonicview Control" software for TASCAM Sonicview 16/24
  　Version         : V1.6.0  （date of latest update: 4 April 2024）

- "TASCAM Sonicview USB for Windows" USB driver for TASCAM Sonicview 16/24
    Version         : V1.0.1   (date of latest update: no update)

- IF-MTR32 32-channel multitrack recording card for TASCAM Sonicview 16/24
　　Firmware        : V1.12   （date of latest update: 13 December 2023）

- SB-16D
    - Firmware      : V1.20  （date of latest update: 4 April 2024）

　　- Dante module firmware
      　<TASCAM SB-16D units with serial numbers No.223xxxx, 226xxxx, 228xxxx（Brooklyn II）>   (date of latest update: no update)
          Product Version             : V1.0.0
          Software Version            : V1.0.0.3
          Firmware Version            : V1.0.0.3
          Dante Firmware Version      : V4.2.3.13

        <TASCAM SB-16D units with serial numbers Serial No.232xxxx and later（Brooklyn 3）>     （date of latest update: 18 October 2023）
          Product Version             : V1.0.1
          Software Version            : V1.0.1.1
          Firmware Version            : V1.0.1.1
          Dante Firmware Version      : V4.2.7.7

- "TASCAM IO CONTROL" software for SB-16D
    Version         : V1.1.1  （date of latest update: 4 April 2024）

<URLs>
 TASCAM Sonicview 16 related :<https://tascam.jp/int/product/sonicview_16/download>
 TASCAM Sonicview 24 related :<https://tascam.jp/int/product/sonicview_24/download>
 TASCAM IF-MTR32 related     ：<https://tascam.jp/int/product/if-mtr32/download>
 TASCAM SB-16D related       :<https://tascam.jp/int/product/sb-16d/download>
=============================================================================================================

--------------------------------------------------------------------------------------------------------------
V1.1.1 (2024.4.4)
--------------------------------------------------------------------------------------------------------------
< Maintenance items >
- The following changes have been added to the GPIO Settings screen:
   IN)  "Local / Open - Mute " settings have been changed to "Local / Closed - Unmute"
   OUT) "Local / Mute - Open " settings have been changed to "Local / Unmute - Closed"
- Operation stability has been improved.


--------------------------------------------------------------------------------------------------------------
V1.1.0 (2023.10.18)
--------------------------------------------------------------------------------------------------------------
< New functions >
- Multiple IO CONTROL apps can now be connected to a single SB-16D unit, with a maximum of 10 simultaneous log-ins, including TASCAM Sonicview 16/24.
- SB-16D control authority can now be transfered within multiple IO CONTROL apps.

< Maintenance items >
- The display unit of the Analog Reference Level has been corrected.
- Operation stability has been improved.

--------------------------------------------------------------------------------------------------------------
V1.0.1 (2023.4.19)
--------------------------------------------------------------------------------------------------------------
< Maintenance items >
The operation of adjusting gain by dragging the mouse has been improved.